There are other pedalboards on the market that are designed so that the
'case' is the 'pedalboard'.
This pedalboard/case all in one design allows the pedalboard contents
to suffer all of the shock, bumps, drops and slams from typical tour
use, simply because your pedals are mounted to the actual case.
In true innovative Trailer Trash fashion, we have designed a pedalboard
that will rest in a 1" foam ATA tray. Our boards are designed either
to take out of the tray, or you can set the ATA case down on the stage,
undo the butterfly latches, lift off the lid, plug in your board, play
a show, while still have it protected by the 1" foam ATA tray. Fast
, easy, and reliable.
We went through many designs to get the play area of the board as low
profile as possible when in the tray. It is comfortable.
This is a proven design. Rascal Flatts guitarist Joe Don Rooney has had
Trailer Trash Pedalboards Products on tour since 2004, and has never
had a break down... This is real touring, forklifts, semi trucks, ramps,
rain, roadies etc...
All of the Trailer Trash Products built for Rascal Flatts are housed
in our Shock Mount ATA Case Design.
The new ATA case from Trailer Trash Pedalboards has been taken one step
further in design. We have addressed the weight issue in everyway possible
since the original conception of the company, and our new ATA cases
are no exception.
We have researched and found new materials on the market that are the
same thickness as the standard wood used by most current case companies.
The composite is much lighter than wood and rates just as high if not
higher.
(Please don't confuse this with the thin plastics used by some rack and
case companies. That is a different catagory.)
The result is that a quality wood ATA case for a 30"x18” pedalboard
typically weighs 30lbs. - 35lbs. That is just the ATA case, not including
the pedalboard, or the contents on the board.
Our new ATA case (30x18) weighs 17lbs without the board inside. 13-18lbs
lighter than industry standard wood cases! This comes in handy when
you are paying the upcharges that airlines charge for excessive weight.
All boards come with patchbays pre-punched and plugged for the player
to install 1/4” inputs/outputs (3 per side) - Pro Series boards
are designed for the power supply to mount under the board. This allows
the player to route the a/c cord out of the side of the board making T-Trash
the Touring pros choice.
(see below) Custom Wired by T-Trash
For this player, we prep’d his board so when he recieved it,
it was a breeze to finish the wiring.
We installed (1) Main A/C - (2) Courtesy A/C’s (1) Top and (1)
side (This is an extra A/C’s for pedals that need A/C power - you
can plug your amp in here too)
We hard wired his power supplies to the side A/C. With these accessories
he only has to plug in the x-cord to the wall and all of the A/C & D/C
are ready to go.
We installed 3 Neutrik locking 1/4” plugs - Guitar ‘IN’ on
the right - Stereo ‘OUT’ on the left.
He sent us his True By-Pass loop boxes and we installed them with audio
and power.
Voila! He only has to build his audio cables and run his D/C cables to
each pedal and within a few hours, he has professional results as seen
in the Trailer Trash Gallery.
TRAILER TRASH CUSTOM WIRING PRICING
[all accessories by direct order only]
Wiring
Pricing is per pedal, according to style of wiring and the style of top
Conventional Wiring – each box is daisy chained
In Loops – each box is wired on a true bypass loop
Please note: All products in addition to pedals, i.e. power sources, buffers, wireless, loopers, etc.. are considered boxes and will apply to the pricing below.
Conventional Wiring - Vel-Top or Hard -Top — $35.00 per box
In Loops – Vel-Top or Hard -Top — $40.00 per box
Conventional Wiring – Glow Top — $45.00 per box
In Loops – Glow Top — $50.00 per box
Cable and Connectors
NEW for 2009!! Evidence monorail cable
(works with George L connectors)
$2.15 ft.
George L's .155 cable
(red, black, white, or blue)
$1.75 ft.
George L's 90 deg end w/ jacket
$6.50 ea.
Locking ¼" connectors – wired
$30.00
Locking ¼" connectors – installed but not wired
$20.00
NEW for 2009!!
Gigrig Humdinger (buffer)
$115.00
Power
Side or top mount a/c wired
(male or female)
$30.00
Side or top mount a/c part only (male or female)
$20.00
10ft power cord
$25.00
D/C connectors
$4.00
Voodoo Lab Pedal Power 2+
installed: $200.00
Voodoo Lab Pedal Power A/C
installed: $170.00
Vel-Pak (for your Vel-Top board)
18" x 16"
$4.00
28" x 16"
$5.00
30" x 18"
$6.00
Tour Grade Velcro (for Hard-Tops & Glow-Tops)
$6.00 ft
Packs of 'C' clamps for securing cables
(These are included in the price when T-Trash is custom wiring your board. They are for sale for the do-it-yourselfer who wants to do a nice job on their own custom wiring)
Multi Pack – Includes screws
$15.00
T-Shirt
Medium, Large, or X Large
(includes shipping for 48 state)
